-
The Edelbrock Supercharger System part #158360 is designed for use on a 2018 Ford F150 with Gen III DI/PI 5.0L Coyote engine and 10-Speed automatic transmission. The heart of this system is the high-efficiency Eaton Gen VI 2650 TVS rotating assembly with a four-lobe design with 170 degrees of twist for maximum flow, minimum temperature rise and quiet operation for excellent drivability. The system also features an integrated bypass valve to help eliminate parasitic loss under light throttle, improving fuel mileage potential. The front drive, front inlet configuration results in a shorter, less restrictive intake path for improved airflow without the need for a power-robbing jackshaft. Keeping the air cool is a high-capacity, Dual-Pass 3-Core (DP3C) air-to-water intercooler and duel pass front-mount heat exchanger. The Edelbrock #158360 system is 50-state emissions legal and provides the best combination of performance and reliability for your F150 whether you plan to tow a trailer, haul heavy loads, or you just want to feel your F-150 come to life! HANDHELD PROGRAMMER NOT INCLUDED. Supercharger systems sold without tuners are only emissions legal when used with the correct Edelbrock program. Which can be requested by contacting the Edelbrock calibration team at calibration@edelbrock.com. Tunes for 91 and 93 octane fuels are available upon request. This system will produce approximately 601whp 468wtq using 93 octane.
Edelbrock supercharger Stage 1 Street system part #15836 is designed for use with 2018 Ford F150 With Gen III DI/PI 5.0L Coyote engine and 10-Speed Auto trans.
Ford:Coyote 4V:302 (5.0L)- Ideal For Towing and Off-Road Performance
-
The Edelbrock supercharger Stage 1 part #158360 is designed for use with 2018 Ford F150 With Gen III DI/PI 5.0L Coyote engine and 10-Speed Auto trans. The core of this system is the Eaton Gen VI 2650 TVS rotating assembly with a four-lobe design with 170 degrees of twist for maximum flow, minimum temperature rise and quiet operation for excellent drivability. We also designed our superchargers with an integrated bypass valve to help eliminate parasitic loss under light throttle, improving mileage potential. Our unique and efficient inlet configuration results in a shorter, less restrictive intake path for improved airflow, without the need for a jack-shaft. Keeping the air cool is a high-capacity air-to-water intercooler and low-temp heat exchanger. The Edelbrock #15836 system is 50-state emissions legal. The supplied tune is intended for completely stock vehicles with the exception of a cat-back exhaust. HANDHELD PROGRAMMER NOT INCLUDED. Supercharger systems sold without tuners are only emissions legal when used with the correct Edelbrock program.
Edelbrock supercharger Stage 1 part #158360 is designed for use with 2018 Ford F150 With Gen III DI/PI 5.0L Coyote engine and 10-Speed Auto trans.
Ford:Coyote 4V:302 (5.0L)- Ideal For Towing and Off-Road Performance
-
Edelbrock introduces its new E-Street 15-degree LS3 69cc cylinder heads (PN 77620) as a premium replacement option, ensuring great power on any high-performance or stock GM LS3 engine build. These heads offer the best performance value of any aftermarket GM LS3 head. Sold in pairs and assembled with premium COMP Cams valve train components, these LS3 heads are engineered with the same architecture as the factory head, and all stock components will fit without issue. The assembled heads feature Beehive(TM) Valve Springs, chromoly steel retainers, heavy-duty stainless-steel valves, and top-quality valve seals – all inspected and assembled by qualified Edelbrock technicians. The intake valve size is 2.165 while the exhaust is 1.590 . The Beehive Valve Springs allow up to .570 lift camshafts, ideal for many mild to hot camshaft grinds. Edelbrock E-Street 15-degree LS3 cylinder heads are manufactured with premium aluminum alloy, machined to the industry’s tightest tolerances. They feature manganese bronze valve guides for extended wear, with particular emphasis placed on holding precision tolerances on valve seat concentricity. This allows the valves to seal securely, eliminating any leak-down and increasing cylinder pressures during engine operation. All Edelbrock cylinder heads feature patented Clean Cast Technology(TM) , a revolutionary process that eliminates casting flaws and promotes a smoother internal surface finish for greater air and coolant flow. These benefits provide more power and increased cooling ability right out of the box. A unique dual spark-plug-pocket design allows you to use the factory-style tapered-seat spark plugs or gasket-seat spark plugs available in wider heat ranges for maximum tunability.
The E-Street Cylinder Heads for GM LS3 are designed as premium quality, bolt-on-ready cylinder heads for any high-performance or stock replacement application. The chambers are 69cc, while the Beehive springs allow .570 lift camshafts.- 2.165″ Stainless Intake Valve, 1.59″ Stainless Exhaust Valve
- Sold in Pairs (2 complete, assembled heads per part number)
- Ready to bolt on out of the box
- GM LS3 Compatible
-
Edelbrock part #1790 is a 80GPH In-Line Electric fuel pump featuring a black anodized aluminum housing and high-quality internals, resulting in both a strong and durable design. The in-line design keeps the pump motor and components cool even under harsh conditions. Compatible with all grades of gasoline and methanol type fuels only. Each pump is factory-tested and includes mounting brackets.
Edelbrock part #1790 is a 80GPH In-Line Electric fuel pump featuring a black anodized aluminum housing and high-quality internals, resulting in both a strong and durable design.- Includes Mounting Brackets
-
The Pro-Flo XT Chrysler 440 #7144 EFI intake manifold is engineered with a large plenum and long tapered runners to deliver maximum horsepower and broad torque band throughout the rpm range 1500-7000 rpm. Features include a 90mm throttle bore opening. This manifold produced 20 more horsepower over our #35090 manifold at 5500 rpm. Accepts Pro-Flo XT throttle body #3869 or Ford throttle body #3818. Compatible with B/B Chrysler XT Fuel Rail Kit #3644 (sold separately).
Edelbrock Pro-Flo XT EFI Intake Manifold for Chrysler 413-426-440 Big-Block V8
Chrysler:Big-Block RB Series:413 (6.8L)/426 (7.0L)/440 (7.2L)- As-Cast Finish
-
The Edelbrock #38783 Victor EFI 4-Barrel Throttle Body complements our Victor EFI line of manifolds. This throttle body mounts on a standard 4150-style square-bore carburetor bolt spacing. It is sand cast, fully machined, and assembled by Edelbrock. The #38783 has 1.75″ Throttle Bores and accepts a Standard (5-1/8″ Flange) Air Cleaner assembly. A 2-Pin Hitachi PWM Style IAC Motor and 3-Pin TPS are included. Satin Finish
The Edelbrock #38783 Throttle Body. Victor EFI. 4-Barrel. 4150-Style Mounting Flange. 1.75″ Bores. Includes PWM IAC Motor ad TPS. Satin Finish- All Stock Sensors And Lines Fit Like Stock
-
The Edelbrock 90mm single bore throttle body is intended for Pro-Flo XT and EFI Victor Elbow applications. It has provisions for either LS1 or LS2 mounting bolt patterns. The throttle body uses LS1 style TPS and IAC. It offers better idle control than other 90mm throttle bodies, because of the addition of an idle bleed screw. By using the bleed screw to create a base amount of idle air flow instead of throttle tip-in, the TPS signal is unaffected. Polished Finish
The Edelbrock #38691, 90mm single bore throttle body, is intended for Pro-Flo XT and EFI Victor Elbow applications. It has provisions for either LS1 or LS2 mounting bolt patterns. The throttle body uses LS1 style TPS and IAC. Polish Finish- All Stock Sensors And Lines Fit Like Stock
-
Edelbrock Part #15834 Remote Oil Filter Mounting Kit is necessary when installing the new Edelbrock supercharger in a ’04-’10 Ford F-150, ’06-’08 Lincoln Mark LT or ’07-’11 Expedition/Navigator equipped with 4WD. This kit relocates the oil filter to clear the front differential. Kit contains all necessary hoses, brackets and hardware.
Edelbrock Part #15834 Remote Oil Filter Mounting Kit is necessary when installing the new Edelbrock supercharger in a 04-10 Ford F-150, 06-08 Lincoln Mark LT or 07-11 Expedition/Navigator equipped with 4WD.
Ford:Modular 3V:281 (4.6L)/330 (5.4L)- Monitors Air/Fuel Ratio
-
For those of you who are running a Pro-Flo 4 EFI on your vehicle and have a damaged ECU, Edelbrock is now offering a replacement unit. Engine Control Unit (ECU) #3543 for the Pro-Flo 4 is a new service item for customers who need to replace a damaged ECU or would like to carry an additional ECU as a spare.
Engine Control Unit (ECU) #3543 for the Pro-Flo 4 is a new service item for customers who need to replace a damaged ECU or would like to carry an additional ECU as a spare. -
no need for custom tuning or a laptop. The included EZ-Street Bluetooth Tuner App, available for both iOS and Android, allows users to configure the system, adjust settings, and monitor performance through intuitive preprogrammed dashboards. Data logging, fuel control, and dual electric fan management are all accessible directly from a smartphone or tablet.
Beyond fuel delivery, the EZ-Street EFI offers the option of fully programmable ignition control, enabling optimized performance and improved fuel efficiency. When paired with a Pro-Flo distributor (sold separately), the EZ-Street EFI can deliver fully integrated timing control at the touch of your fingers. With an internal coil driver and compatibility across most HEI distributors, ready-to-run distributors, and CDI boxes, the system eliminates the need for separate ignition modules. Capable of supporting up to 650 horsepower, the EZ-Street EFI system combines advanced annular-fuel-venturi distribution with modern CAN communication protocols to provide reliable, high-performance results in a simplified package.
Engineered to provide an affordable and user-friendly upgrade for any V8 engine originally equipped with a carburetor, the EZ-Street EFI system seamlessly integrates cutting-edge technology with traditional styling.
Supports 650 hp, 4150 Flange, 1000 CFM, Classic looks of a traditional carburetor, Highly refined base tunes to chose from plus self learning technology, Bosch LSU 4.9 Wideband O2 sensor included, Complete Spark Control, Built in ignition coil driver, Built in Bluetooth communication, Easy to use E-Tuner app for Android and IOS, CAN Communication, Simple 4 wire hookup- Supports 650 horsepower, Built in fuel pressure sensor, Standard 4150 flange, Classic Carburetor looks, Uses common linkages and air cleaners, Offers full spark control or fuel control only depending on users needs
- Built in coil driver, Bosch LSU 4.9 Wideband O2 sensor, Closed loop, Self Learning fueling technology, CAN Communication simplifies integration with other devices such as Transmission Controllers
- Compact, fully potted ECU with built in Bluetooth communication, Android and IOS E-Tuner app for simple and clean setup and engine monitoring, Simple 4 wire hookup for easy installation
- E-Tuner app offers easy setup, changes, and monitoring with crisp, clear graphics and easy navigation
- Choice of three calibrations offers great out of the box performance even with big camshafts
- Supports 650 horsepower
-
Edelbrock Coil Pack #22783 is a set of eight coil-on-plug coils designed as direct performance replacements for the OEM coils on 2004-08 Ford 4.6L-5.4L 3-valve V8 engines. Each coil in the #22783 pack features advanced technology with heavy-duty primary and secondary windings inside of a corrosion-resistant housing. The enhanced windings in these coils offer higher energy and voltage output for greater spark and can help to provide quicker starts with improved idle quality. Coil housings are resistant to heat, shock, vibration and corrosion. This coil is also sold individually under #22782.
COIL ON PLUG 2004-08 FORD V8 4.6L-5.4L 3 VALVE ENGINE (SET OF 8)
Ford V8 4.6L-5.4L; 2004-08- Max Fire Coil-On-Plug Set
-
Edelbrock part #7581 RPM Air-Gap 351W intake manifold is designed for street and high performance 351-427 c.i.d. 351W Ford V8 applications. The RPM Air-Gap incorporates the same race-winning design that’s been used on our Victor Series competition intakes for decades. The Air-Gap design features an open air space that separates the runners from the hot engine oil resulting in a cooler, denser charge for more power. Larger cross sectional area and a taller carb flange than #7181 for compatibility with large displacement, stroker 351W based engines. Includes bosses for nitrous and rear water crossover. Edelbrock carbs will work with Ford automatic overdrive trans (AOD) when used with Lokar bracket SRK-4000, for more info call (865) 966-2269 or go to www.lokar.com.
Edelbrock Performer RPM Air-Gap Intake Manifold for 351W Ford Small Block Windsor engines
Ford:Small-Block Windsor:351W (5.8L)-427 (7.0L)- Compatibility w/Large Displacement 351W Based Eng.
Showing 23281–23292 of 55774 results