Shop

Unlock 50-70+HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2 Boost Cooler water-methanol injection system is available for all forced induction applications (supercharged/turbocharged). The Stage 2 uses the progressive VC-50 controller (52mm Gauge) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. The VC-50 (ISO 9001 Manufactured) controller offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to your OEM gauges or mix and match up to two colors.. Comes with easy to install quick-connect fittings and 1/4″ high temp nylon tubing.
Stage 2 Boost Cooler(tm) Forced Induction Progressive Water-Methanol Injection Kit (Red High Temp Nylon Tubing, Quick-Connect Fittings)
Kit Contents: 300 PSI UHO Pump, 3Qt Tank, Adjustable Progressive VC-50 Controller/Harness, (20′) Red High Temp Nylon Tubing, Boost Line/Required Hardware, Required Quick-Connect Fittings, SP Decal, Self Sealing Level Sensor, Snow Performance Hypersonic-Water-Meth Nozzles/High Flow Check Valve

• Adjustable Boost Activated Progressive Water-Meth Delivery
• 300 PSI UHO Pump/SP Hypersonic Nozzles
• 100% Methanol Resistant
• High Flow Check Valve
• Low Level Monitoring
• Made In U.S.A.

Race gas quality fuel on pump gas! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 1 Boost Cooler water-methanol injection kit is available for all forced induction applications (supercharged/turbocharged) and uses a adjustable boost switch to inject a fixed amount of water-methanol into the system until boost goes below the switch set point. Proven to deliver 30-70 HP increases to all forced induction applications! This makes it a good choice for low to medium boost setups (1-15 PSI) and vehicles with a positive displacement supercharger looking for an octane enhancement and cooler intake charge. Activation can also be set up through any other user-chosen switch, such as a full throttle switch, nitrous switch, etc. Comes with easy to install quick-connect fittings and 1/4″ high temp nylon tubing.
Stage 1 Boost Cooler(tm) Forced Induction Water-Methanol Injection Kit (Red High Temp Nylon Tubing, Quick-Connect Fittings)
Kit Contents: 300 PSI UHO Pump, 3Qt Tank, Adjustable Boost Pressure Switch/Relay, 20 AMP Fuse/Fuse Holder, (20′) Red High Temp Nylon Tubing, Boost Line/Required Hardware, Required Quick-Connect Fittings, SP Decal, Self Sealing Level Sensor, LED Alert System, Snow Performance Hypersonic-Water-Meth Nozzles/High Flow Check Valve

• Adjustable Boost Activated Water-Meth Engagement
• 300 PSI UHO Pump/SP Hypersonic Nozzles
• 100% Methanol Resistant
• High Flow Check Valve
• Low Level Monitoring
• LED Alert System
• Made In U.S.A.

Unlock 50-70+HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2 Boost Cooler water-methanol injection system is available for all forced induction applications (supercharged/turbocharged). The Stage 2 uses the progressive VC-50 controller (52mm Gauge) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. The Stage 2 introduces the VC-50 Controller (ISO 9001 Manufactured). The VC-50 offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to your OEM gauges or mix and match up to two colors. Comes with 4AN fittings and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.
Stage 2 Boost Cooler(tm) Forced Induction Progressive Water-Methanol Injection Kit (Red High Temp Nylon Tubing, Quick-Connect Fittings)No Tank – No Tank

Race gas quality fuel on pump gas! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 1 Boost Cooler water-methanol injection kit is available for all forced induction applications (supercharged/turbocharged) and uses a adjustable boost switch to inject a fixed amount of water-methanol into the system until boost goes below the switch set point. Proven to deliver 30-70 HP increases to all forced induction applications! This makes it a good choice for low to medium boost setups (1-15 PSI) and vehicles with a positive displacement supercharger looking for an octane enhancement and cooler intake charge. Activation can also be set up through any other user-chosen switch, such as a full throttle switch, nitrous switch, etc. Comes with 4AN fittings and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.
Stage 1 Boost Cooler(tm) Forced Induction Water-Methanol Injection Kit (Stainless Steel Braided Line, 4AN Fittings)
Kit Contents: 300 PSI UHO Pump, 3Qt Tank, Adjustable Boost Pressure Switch/Relay, 20 AMP Fuse/Fuse Holder, (1) 1′, (1) 2′, (1) 5′ Stainless Steel Braided Line, Boost Line/Required Hardware, Required 4AN Fittings, SP Decal, Self Sealing Level Sensor, LED Alert System, Snow Performance Hypersonic-Water-Meth Nozzles/High Flow Check Valve

• Adjustable Boost Activated Water-Meth Engagement
• 300 PSI UHO Pump/SP Hypersonic Nozzles
• 100% Methanol Resistant
• High Flow Check Valve
• Low Level Monitoring
• LED Alert System
• Made In U.S.A.

Decrease EGTs and increase HP in your diesel by 65HP+ in the most cost effective water-methanol injection kit on the market! Utilizing a adjustable boost pressure switch and dual nozzles to deliver precise amounts of water-methanol once 30 boost PSI has been reached (Boost Engagement Adjustable, 30 PSI Boost Hobbs Switch Included). Recommended for all high boost and competition diesels looking to increase HP while decreasing EGTs when on heavy throttle. Comes with easy to mount race ready 3QT tank, high flow check valve, quick-connect fittings, 300 PSI UHO Pump, and LED alert system.
Diesel Stage 1 Boost Cooler(tm) Water-Methanol Injection Kit (Red High Temp Nylon Tubing, Quick-Connect Fittings)
Kit Contents: 300 PSI UHO Pump, 3Qt Tank, Adjustable Boost Pressure Switch/Relay, 20 AMP Fuse, (20′) Red High Temp Nylon Tubing, Boost Line/Required Hardware, Required Quick-Connect Fittings, SP Decal, LED Alert System, Dual Nozzle Upgrade, Snow Performance Hypersonic-Water-Meth Nozzles/High Flow Check Valve

• Adjustable Boost Activated Water-Meth Engagement
• 300 PSI UHO Pump/SP Hypersonic Nozzles
• 100% Methanol Resistant
• Dual Water-Meth Nozzles
• LED Monitoring system
• High Flow Check Valve
• Made In U.S.A.

Unlock 50-70+HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2 Boost Cooler water-methanol injection system is available for all forced induction applications (supercharged/turbocharged). The Stage 2 uses the progressive VC-50 controller (52mm Gauge) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. The Stage 2 introduces the VC-50 Controller (ISO 9001 Manufactured). The VC-50 offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to your OEM gauges or mix and match up to two colors. Comes with 4AN fittings and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.
Stage 2 Boost Cooler(tm) Forced Induction Progressive Water-Methanol Injection Kit (Stainless Steel Braided Line, 4AN Fittings) No Tank – No Tank

Unlock 50-70+HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2 Boost Cooler water-methanol injection system is available for all forced induction applications (supercharged/turbocharged). The Stage 2 uses the progressive VC-50 controller (52mm Gauge) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. The Stage 2 introduces the VC-50 Controller (ISO 9001 Manufactured). The VC-50 offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to your OEM gauges or mix and match up to two colors. Comes with 4AN fittings and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.
Stage 2 Boost Cooler(tm) Forced Induction Progressive Water-Methanol Injection Kit (Stainless Steel Braided Line, 4AN Fittings)
Kit Contents: 300 PSI UHO Pump, 3Qt Tank, Adjustable Progressive VC-50 Controller/Harness, (1) 1′, (1) 2′, (1) 5′ Stainless Steel Braided Line, Boost Line/Required Hardware, Required 4AN Fittings, SP Decal, Self Sealing Level Sensor, Snow Performance Hypersonic-Water-Meth Nozzles/High Flow Check Valve

• Adjustable Boost Activated Progressive Water-Meth Delivery
• 300 PSI UHO Pump/SP Hypersonic Nozzles
• 100% Methanol Resistant
• High Flow Check Valve
• Low Level Monitoring
• Made In U.S.A.

Unlock 50-70+HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2 Boost Cooler water-methanol injection kit is available for all forced induction applications (supercharged/turbocharged) and uses a progressive controller with built in manifold absolute pressure (MAP) sensor that proportionally injects more or less water-methanol according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. Comes with adjustable progressive VC-20 engine mount controller, 4AN fittings, and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.
Stage 2 Boost Cooler(tm) Forced Induction Progressive Engine Mount Water-Methanol Injection Kit (Stainless Steel Braided Line, 4AN Fittings)
Kit Contents: 300 PSI UHO Pump, 3Qt Tank, Adjustable Progressive VC-20 Controller/Harness, (1) 1′, (1) 2′, (1) 5′ Stainless Steel Braided Line, Boost Line/Required Hardware, Required 4AN Fittings, SP Decal, Self Sealing Level Sensor, LED Alert System, Snow Performance Hypersonic-Water-Meth Nozzles/High Flow Check Valve

• Adjustable Boost Activated Progressive Water-Meth Delivery
• 300 PSI UHO Pump/SP Hypersonic Nozzles
• 100% Methanol Resistant
• High Flow Check Valve
• Low Level Monitoring
• LED Alert System
• Made In U.S.A.