Shop

Edelbrock part #2858 Victor Glidden Spider intake manifold is intended for 375 c.i.d and up high output drag race engines. This manifold was developed in conjunction with noted drag racer Billy Glidden and is specifically designed to complement the flow characteristics of fully ported 18-degree and 15-degree cylinder heads. It features a 4500 series carb flange, and the dividers are pulled back to increase plenum size and shorten the runners for improved high rpm performance. The runners are wider at the plenum, producing approximately 3.6 square inches area at the opening. The Edelbrock Victor Glidden Spider is a single-plane, high-rise intake designed for maximum race-winning power at higher engine speeds.
Edelbrock Victor Glidden 15-18 Degree Spider Intake Manifold For 15 and 18 Degree Chevy for 4500 Series Carburetors
Chevrolet:Small-Block Gen I Race

• Carburetor Mounting Flange For 4500-Series Carb

Edelbrock part #29215 Victor Jr. 302 EFI intake manifold is designed for use with Ford 289-302 competition engines using modified stock cast iron or aftermarket Windsor-style cylinder heads such as Edelbrock #60259 and #77169 or equivalent. Victor Jr. EFI also features bosses for rear water crossover. Port exit size at cylinder head is 1.08″ x 1.90″ with extra material to accommodate a 1.18″ x 2.10″ opening. The Edelbrock Victor Jr. #29215 EFI is a single-plane, high-rise intake designed for maximum race-winning power at higher engine speeds.
Edelbrock Victor Jr. 302 EFI Intake Manifold for Ford 289-347 Small-Block V8
Ford:Small-Block Windsor:260 (4.3L)/289 (4.7L)/302 (5.0L)

• Port Exits Can be Opened to 2.10 x 1.18 in.

Edelbrock part #2826 Super Victor LS3 carbureted intake manifold is designed for Gen IV LS engines equipped with LS3 cylinder heads. This new Super Victor intake manifold is ideal for anyone building a 700+ hp 4150 series carbureted large displacement racing engine operating between 3,500 – 7,500 rpm. This new Super Victor intake manifold is designed with 24% larger runners than our Victor Jr. #28457 along with a larger 4500 style plenum. The large plenum makes this intake manifold ideal for nitrous and forced induction applications. This intake manifold also features tapered runners for increased flow at high rpm. A carburetor mounted style throttle bracket is recommended.
Edelbrock Super Victor LS3 Carbureted Intake Manifold for Small-Block Chevrolet Gen IV Engines with LS3, L92, & L76 Rectangle Port Cylinder Heads. Accepts 4150-Series Carburetor. Non-EGR.
Chevrolet:Small-Block Gen IV L76:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV L92:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV L99:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV LS3:364 (6.0L)/376 (6.2L)

• Use For Any Application Requiring Maximum Power

Edelbrock part #2821 Super Victor LS3 intake manifold is designed for Gen IV LS engines equipped with LS3 cylinder heads, this new Super Victor intake manifold is ideal for anyone building a 700+ hp 4500 series carbureted large displacement racing engine operating between 3,500 – 7,500 rpm. This new Super Victor intake manifold is designed with 24% larger runners than our Victor Jr. #28457 along with a larger 4500 style plenum. The large plenum makes these intake manifolds ideal for nitrous and forced induction applications. They also feature tapered runners for increased flow at high rpm. The Super Victor 4500 series manifolds can accommodate bores up 2.25″. A carburetor mounted style throttle bracket is recommended.
Edelbrock Super Victor LS3 Carbureted Intake Manifold for Small-Block Chevrolet Gen IV Engines with LS3, L92, & L76 Rectangle Port Cylinder Heads. Accepts 4500-Series Carburetor. Non-EGR.
Chevrolet:Small-Block Gen IV L76:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV L92:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV L99:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV LS3:364 (6.0L)/376 (6.2L)

• Use For Any Application Requiring Maximum Power

Edelbrock part #28265 Super Victor LS3 EFI intake manifold is designed for Gen IV LS engines equipped with LS3 cylinder heads. This new Super Victor intake manifold is ideal for anyone building a 700+ hp 4150 series EFI large displacement racing engine operating between 3,500 – 7,500 rpm. The large plenum makes this intake manifold ideal for nitrous and forced induction applications. This EFI intake manifold also features tapered runners for increased flow at high rpm. A carburetor mounted style throttle bracket is recommended.
Edelbrock EFI Super Vic LS3 4150 Intake Manifold GM LS Engines
Chevrolet:Small-Block Gen IV L76:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV L92:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV L99:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV LS3:364 (6.0L)/376 (6.2L)

• Use For Any Application Requiring Maximum Power

Edelbrock part #28215 Super Victor LS3 EFI intake manifold is designed for Gen IV LS engines equipped with LS3 cylinder heads. This new Super Victor intake manifold is ideal for anyone building a 700+ hp 4500 style EFI large displacement racing engine operating between 3,500 – 7,500 rpm. This Super Victor intake manifold is designed with 24% larger runners than our Victor Jr. #28455 along with a larger 4500 style plenum. The large plenum makes this intake manifold ideal for nitrous and forced induction applications. The manifold also features tapered runners for increased flow at high rpm. The Super Victor 4500 series manifolds can accommodate bores up 2.25″. This Super Victor LS3 EFI intake manifold includes machined fuel injector bosses. A carburetor mounted style throttle bracket is recommended.
Edelbrock Super Victor LS3 EFI 4500 Style Intake Manifold for Gen IV LS3
Chevrolet:Small-Block Gen IV L76:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV L92:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV L99:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV LS3:364 (6.0L)/376 (6.2L)

• Use For Any Application Requiring Maximum Power

Edelbrock part #2790 Torker 308 intake manifold is designed for Holden 253-304-308 c.i.d. V8 engines with Red motor cylinder heads only (with single bolt in center of manifold), will not fit on Blue/Black cylinder head engines. The Torker 308 intake manifold is a single-plane design and is recommended for street high performance and race engines operating between the 2500 to 6500 rpm range where low-end torque is not required. Accepts square-bore carbs only.
Edelbrock Torker 308 Intake Manifold for Small-Block Holden Engines is Designed for 253-304-308 C.I.D. V8’s with Red Motor Cylinder Heads. Will Not Fit Black/Blue Cylinder Heads. Accepts a 4150-Style Square-Bore Carburetor. Non-EGR.
Holden:Small-Block VN:308 (5.0L)/355 (5.7)/383 (6.3L)

• Manifold Not Equipped with EGR

Edelbrock part #50565 Torker II Pontiac EFI intake manifold is designed for 1965-79 street 389-455 c.i.d. Pontiac V8’s. Can be used with Ram Air IV heads. Will not fit Ram Air V and 265/301 V8’s or under Trans Am Shaker hood.
Edelbrock Torker II EFI Pontiac Intake Manifold for Pontiac 326-455 V8
Pontiac:-:326 (5.3L)/350 (5.7L)/389 (6.4L)/400 (6.6L)/421 (6.9L)/428 (7.0L)/455 (7.4)

• For Standard 351-W Blocks with 9.5-in. Deck

Edelbrock part #2812 Victor Oldsmobile intake manifold provides power levels never before available for competition single-carb 350-403 Olds engines. Featuring a single-plane “Air-Gap” design, it accepts square-bore carb and offers significant horsepower increases over existing intakes in the 4500 to 7500 rpm range. It features a carb mount pad height of 7″ and high-flow constant area 3.2-square-inch runners. The runners have been optimized to match the flow characteristics of Edelbrock Performer RPM aluminum cylinder heads #60519 and the exit size, as-cast, is 1.28″ by 1.94″ with plenty of metal thickness for gasket matching and porting.
Edelbrock Victor Olds 350-403 Intake Manifold for 350-403 c.i.d Oldsmobile Small-Block Engines is Designed for High-Performance Competition & Marine Engines. Accepts a 4150-Style Square-Bore Carburetor. Non-EGR.
Oldsmobile:Small-Block:307 (5.0L)/330 (5.4L)/350 (5.7L)/403 (6.6L)

• Any Carburetor Class Allows

Edelbrock part #28457 Victor JR. LS3 intake manifold is designed for Gen IV LS engines equipped with LS3, L92 and L76 cylinder heads. This manifold is for carbureted racing applications operating between 3500-7500 rpm. This manifold uses a standard square bore carb flange that is compatible. The LS3, L92 and L76 all use the same cylinder head.
Edelbrock Victor Jr Carburetor LS3/L92/L76 Intake Manifold GM LS Engines
Chevrolet:Small-Block Gen IV L76:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV L92:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV L99:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV LS3:364 (6.0L)/376 (6.2L)

• Gen IV LS Engines With L92 Heads

Edelbrock part #28455 Victor JR. LS3 intake manifold is designed for Gen IV LS engines equipped with LS3, L92 and L76 cylinder heads. This manifold is for EFI racing applications operating between 3500-7500 rpm. This manifold uses a standard square bore throttle body flange that is compatible with both Edelbrock EFI intake elbows with single bore 90mm throttle body or four-barrel #4150 throttle bodies. This intake has additional bosses and machining that allow for the use of fuel injectors when combined with the #3638 fuel rail kit (sold separately).
Edelbrock Victor Jr LS3/L76/L92 GM EFI Intake Manifold GM LS Engines
Chevrolet:Small-Block Gen IV L76:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV L92:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV L99:364 (6.0L)/376 (6.2L);Chevrolet:Small-Block Gen IV LS3:364 (6.0L)/376 (6.2L)

• Gen IV LS Engines With L92 Heads

Edelbrock part #2810 Victor Oldsmobile 455 drag racing intake manifold provide power levels never before available for competition single-carb 455 Olds engines. In independent flow testing, our port-matched design out-flowed the best fully ported manifolds on the market. Featuring a single-plane “Air-Gap” design, they are available for square-bore or 4500 Series carbs to accommodate many competition applications, and offer significant horsepower increases over existing intakes in the 4500 to 7500 rpm range. With a carb mount pad height of 8.2″, this manifold stand more than three inches taller than the Edelbrock Torker manifold and incorporate a high-flow 3.4-square-inch runner. We’ve removed the intake bolts between the runners, thus creating a smoother airflow path for higher airflow and more power! This intake manifold features a port size and shape that has been optimized to match the flow characteristics of Edelbrock Performer RPM #60519 aluminum cylinder heads.
Edelbrock Victor Olds 455 Intake Manifold for 400-425-455 Big-Block Oldsmobile Engines is Designed for High-Performance Competition & Marine Engines. Accepts a 4150-Style Square-Bore Carburetor. Non-EGR.
Oldsmobile:Big-Block:400 (6.6L)/425 (7.0L)/455 (7.5L)

• Accepts Standard Flange Square Bore Carburetor