Carburetor Rebuild Components

The Edelbrock #1154 Rebuild kit has everything needed to rebuild any Edelbrock 94 carburetor. Includes fuel inlet seat, fuel inlet needle, accelerator pump assembly, accelerator pump spring, accelerator check ball, check ball retainer, power valve assembly, float gauge and all necessary gaskets
Carburetor Rebuild Kit for Edelbrock 94 Carburetors

The Edelbrock part #1034 Non-Progressive Linkage Kits are designed to facilitate the synchronous operation of multiple two-barrel carburetors. The #1034 is designed to support triple two barrel applications.- If you have another make or model of manifold, it may be necessary to alter some of the details of this installation. This kit has a relatively universal application and can be safely installed in a variety of configurations- It is recommended that the linkage be installed with the manifold out of the vehicle, sitting on a level surface. A throttle linkage control arm and ball end stud are provided to connect to the vehicle’s throttle rod or cable. Identify where the vehicle’s throttle rod or cable will terminate so that the linkage control arm can be mounted to the linkage operating shaft accordingly. Also make note of any valve cover features that could interfere with the linkage, such as breathers and/or PCV valves.- All adjustments made to the carburetor arms should be conducted with all carbs at the wide open throttle position to ensure synchronized operation of such.- Be sure to always check that the arms will not become inverted after any adjustment. Some trial and error will berequired to achieve a properly balanced set up.- Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
The Edelbrock 1034 throttle linkage kit is a non-progressive linkage for Triple (3) Edelbrock 94 carburetors. The kit comes with return spring and bracket, linkage with provision for kick down and throttle connection.

The Edelbrock part #1033 Progressive Linkage Kit is designed to smooth throttle response, eliminate flat spots and improve fuel economy. It achieves this by only opening the center carburetor at less than 50% (or 33%) pedal travel thus sharpening the venturi signal and eliminating the bottom end bog found in traditional multiple carburetor setups that open simultaneously. This kit can also be installed in a non-progressive configuration, if so desired, or can progressively operate a dual two-barrel carburetor configuration.- Due to the need for making fine adjustments and inspections, Edelbrock recommends installing the carburetors and linkage kit prior to installing the manifold on the engine. If you have another make or model of manifold, it may be necessary to alter some of the details of this installation. This kit has a relatively universal application and can be safely installed in a variety of configurations- Capped rod may require trimming to clear the manifold- If you have another make or model of manifold, it may be necessary to alter some of the details of this installation. This kit has a relatively universal application and can be safely installed in a variety of configurations- Be sure to always check that the arms will not become inverted after any adjustment. Some trial and error will berequired to achieve a properly balanced set up- Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
The Edelbrock 1033 throttle linkage kit is an adjustable progressive linkage kit for triple (3) Edelbrock 94 2 bbl carburetors. The kit comes with return spring, bracket and linkage with provision for throttle connection.

The Edelbrock #8951 Choke Block-Off For?Small Block Oldsmobile for #3711 Intake Manifold
The Edelbrock Choke Block-Off For Small Block Oldsmobile for #3711 Intake Manifold
Oldsmobile:-:307 (5.0L)-403 (6.6L);Oldsmobile:-:400 (6.6L)-455 (7.5L)

The Edelbrock 94 Carburetor choke bracket kit #1156 provides users with a means of holding a manual choke cable in place upon attaching the cable pull to the carburetor. It includes the bracket and associated hardware. It is a replica of the original Ford bracket that mounted to the carburetor.
The Edelbrock 94 Carburetor choke bracket kit provides users with a means of holding a manual choke cable in place upon attaching the cable pull to the carburetor. It includes the bracket and associated hardware.

The Edelbrock Carburetor Choke Cable Bracket & Clamp assembly #1494 provides users with a means of holding a manual choke cable in place upon attaching the cable pull to the carburetor. The kit includes the bracket and associated hardware.
The Edelbrock Carburetor Choke Cable Bracket & Clamp assembly #1494 provides users with a means of holding a manual choke cable in place upon attaching the cable pull to the carburetor.

The Edelbrock #1995 Choke Cap Kit includes all the components needed to replace the existing choke cap on Edelbrock #1903 Q-Jet Carburetor.
Edelbrock Replacement Choke Cap For 1903

The Edelbrock #1996 Choke Cap Kit includes all the components needed to replace the existing choke cap on Edelbrock #1904, #1905, #1906 and #1910 Q-Jet Carburetors.
Edelbrock Choke Cap For 1904/1905/1906/1910

The Edelbrock #1474 Choke Cap Kit includes all the components needed to replace the existing choke cap on all Edelbrock square bore carbs.
Edelbrock Choke Cap Kit (Includes Choke Cap and Gasket, 3 Screws and 3 Locking Tabs)

The Edelbrock part #9172 Automatic divorced choke rod was designed to be used with Edelbrock Intake Manifold part #7104 with a Q-Jet carburetor. The Edelbrock 9172 Automatic Divorced Choke Rod will allow for a simple installation. Comes with a retaining clip.?
Automatic divorced choke rod for Edelbrock Intake Manifold part #7104 with a Q-Jet carburetor
Chevrolet:Small-Block Gen I:262 (4.3L)-400 (6.6L)

The Edelbrock part #9178 Automatic divorced choke rod was designed to be used with Edelbrock Intake Manifold part #7164 with a Q-Jet carburetor. The Edelbrock #9178 Automatic Divorced Choke Rod will allow for a simple installation. Comes with a retaining clip.?
Automatic divorced choke rod for Edelbrock Intake Manifold part #7164 with a Q-Jet carburetor
Chevrolet:Big-Block Mark IV:396 (6.5L)-502 (8.2L)

The Edelbrock part #9171 Automatic divorced choke rod was designed to be used with Edelbrock Intake Manifold part #2101, 2104 and 3701 with a Q-Jet carburetor. The Edelbrock 9171 Automatic Divorced Choke Rod will allow for a simple installation. Comes with a retaining clip.?
Automatic divorced choke rod for Edelbrock Intake Manifold part #2101, 2104 and 3701 with a Q-Jet carburetor
Chevrolet:Small-Block Gen I:262 (4.3L)-400 (6.6L)