Standalone · Motorsport
Custom MaxxECU setups
Some builds stop being something a factory ECU can describe. A swapped engine, a turbo outside the factory model, individual throttle bodies, ethanol, a sensor set nobody at the factory imagined — at that point the honest answer is to replace the strategy rather than keep arguing with it.
We specify, wire, map and log MaxxECU installations in house. What follows is what a build involves, which tier suits which engine, and the order it happens in.
Custom MaxxECU setups
Not the step after Stage 3 — the other direction. When a build stops being something the factory ECU has a strategy for, the answer is to replace the strategy rather than argue with it. We specify, wire, map and log MaxxECU installations in house.
A swapped engine, a turbo the factory model cannot describe, ethanol, individual throttle bodies, a sensor set nobody at the factory imagined: each of these is a reason the stock ECU starts guessing. MaxxECU runs the engine on tables we build from your hardware, on a loom we can account for pin by pin.
What a flash cannot reach
Every table, not the ones left unlocked
A flash edits what the factory strategy exposes. Standalone replaces the strategy, so fuel, ignition, boost and limits are yours from a blank sheet rather than borrowed from a map somebody else locked.
Sensors the factory never fitted
Flex fuel, fuel pressure, oil pressure and temperature, EGT per cylinder, wheel speed. A factory ECU has nowhere to put them; here they are inputs the calibration can act on.
Closed-loop boost that means it
Boost by gear, by ethanol content, by intake temperature, or on a rotary switch on the dash. Target and correction, not a duty-cycle table and a hope.
Motorsport strategies as standard
Launch control, flat shift, antilag and traction control are part of the platform rather than something a factory ECU has to be tricked into approximating.
Engine swaps stop being a wiring problem
A different engine in a different chassis has no factory calibration to inherit. Standalone is how that car runs properly instead of running at all.
Logging built for reading afterwards
High-rate internal logging in MTune, and live gauges on a tablet through MDash. Every change we make on the dyno is a log you keep.
Choosing the tier
The engine decides the channel count and the rulebook decides the rest. We specify the tier against the build rather than selling up from it.
The entry into standalone management for a street car that has outgrown its factory ECU. Sequential fuel and ignition, closed-loop boost, and enough input for the sensors a road build actually runs.
More input and output than STREET, which is what a car with drive-by-wire, a second lambda and real traction control needs before the harness starts running out of pins.
The tier most of our German builds land on: enough channels to run a V8 or a straight-six fully sequential with individual cylinder trim, and the I/O for a motorsport sensor set.
For a car built to a class rather than to a road. Specify it when the rulebook, the data logging requirement or the sensor count decides the ECU rather than the engine does.
Bench to handover
Engine, chassis, gearbox, fuel, and what the car is actually for. This decides the tier and the sensor list, and it is the conversation that stops a build being specified twice.
A plug-in adapter where one exists for the platform, and a built-to-fit loom where one does not. Motorsport-spec on request, labelled and documented either way.
Wideband lambda, fuel and oil pressure, temperatures, trigger and cam sync verified on a scope before the engine is asked to start.
Built in MTune from the engine's geometry and the injectors actually fitted, then cranked, timed and idled before it goes near a load cell.
Power is the short part. Cold start, idle, transient fuelling and part throttle are what decide whether you can live with the car afterwards.
You leave with the map, the logs, MTune on your laptop and a walkthrough of what to watch. Remote revisions afterwards are part of the build, not an extra.
Standalone management removes the factory emissions strategy and its diagnostics. A car running MaxxECU is a closed-course vehicle. We will say so on the quote, on the invoice and again at handover.